Prilagođena instalacija:Sony XAV-AX7000 u Ford Thunderbird iz 1962.
U ovom članku: Proći ćemo kroz prilagođenu instalaciju Sony XAV-AX7000 u ploču Ford Thunderbird iz 1962. Pun fotografija i uvida!
- Predstavljamo Thunderbird za 1961.
- Učenje stare 'ptice novim trikovima
- Prvi dio:Moderna glavna jedinica
- Ugradnja Sony XAV-AX7000
- Drugi dio:Moderni zvučnici
- Izrada nosača
- Treći dio:Skriveni USB priključci
- Četvrti dio:Instalacija pričuvne kamere
- Završetak projekta
- Cijena instalacije
Predstavljamo Thunderbird za 1961.
Ford je predstavio treću generaciju Thunderbirda u ljeto 1960. Novi dizajn nije bio sličan ničemu na cesti u to vrijeme, što je svakako opravdavalo reklamni slogan tvrtke - "Nepogrešivo novo, nepogrešivo Thunderbird." Automobil je imao dugačak, nizak profil s jasno zašiljenim prednjim krajem koji se sužavao prema sićušnim perajama na stražnjoj strani. Ogromna, okrugla, kromirana stražnja svjetla se ističu, izgledaju ni manje ni više nego kao mlazni turbinski motori i prava su ljepota noću. Automobil u obliku izrazito municije zaradio je nadimak "Ptica metak".
Prodaja je bila pristojna, ali nije dostigla rekordne brojke prethodne generacije, poznate kao "Square Birds". Značajke poput zakretnog upravljača i potpuno novog V8 motora od 390 kubičnih inča jednostavno nisu premostile jaz između onoga kako su vozači željeli da automobil izgleda i onoga kako je izgledao novi Thunderbird. Godine 1964. Ford se vratio uglađenom stilu s četvrtom generacijom Thunderbirda. Prodaja je skočila s vrhunca serije 3. generacije od 73.000 (1961.) na 93.000 (1964.).
Mnogi klasični automobili ispočetka su bili premalo cijenjeni ili čak nepoželjni, da bi postali rijetki i poželjni, ako ni zbog čega drugog, a ono zbog svoje neobične povijesti. Bullet Birds nikada nisu napravili takav skok. Dok su cijene druge i četvrte generacije Thunderbirda skočile posljednjih godina, Bullet Bird je čamio u kategoriji "ne isplati se restaurirati". Vozljivi, s malom kilometražom, nerestaurirani automobili mogu se dobiti za manje od 10.000 USD, a za restauratore koji žele oživjeti lešinu Ptice metka, automobili se mogu dobiti za manje od 1.000 USD.
Ironija Bullet Birda je da kada posjetitelji sajma automobila vide jedan od ovih sada neuobičajenih automobila, općenito vjeruju da je vozilo neka vrsta običaja. Masivni kromirani odbojnici i ukrasi od nehrđajućeg čelika koji se protežu od prednje do stražnje strane nemaju blijed tvornički izgled koji mnogi ljudi povezuju s originalnim automobilima, a čudne linije sigurno ne izgledaju kao dizajni iz ranih 1960-ih koji su većini ljudi poznati.
Tražite odličnu glavnu jedinicu? Pogledajte naše najbolje popise!
Najbolji DVD i video uređaji za automobile u 2022.
Najbolji stereo uređaji i glavne jedinice za automobile u 2022.
Najbolji digitalni multimedijski stereo uređaji za automobile u 2022.
Najbolji GPS navigacijski stereo uređaji za automobile u 2022.
Najbolji bežični Apple CarPlay stereo uređaji za automobile u 2022.
Najbolji iDatalink kompatibilni stereo uređaji za automobile u 2022.
Najbolji automobilski stereo uređaji sa zaslonom osjetljivim na dodir u 2022.
Najbolji jednostruki DIN automobilski stereo uređaji i glavne jedinice u 2022.
Učenje stare 'ptice novim trikovima
Od djetinjstva sam bio opsjednut Bullet Birdom. Sjećam se da sam otišao na tjedno okupljanje automobila i vidio crveni Thunderbird iz 1961. s istom unutrašnjošću od crvenog vinila kad sam vjerojatno imao oko 12 godina. Sav taj krom i ta luda stražnja svjetla stvarno su utjecali na mene i nikada se toga nisam oslobodio zaljubljenost.
Kad mi se ukazala prilika da nabavim nerestaurirani Thunderbird iz 1962. koji je pokazivao samo 83.000 milja na šesteroznamenkastim mjeraču kilometara, uskočio sam. Auto je bio solidan, ali tužan. Koliko mogu reći, bio je parkiran 1968., pokušao se vratiti na cestu 1989., a onda ništa. Samo je stajao dok ga nisam kupio 2016.
Automobilu je bilo potrebno mnogo posla da bi bio vrijedan ceste, a trebalo je malo više od dvije godine rada vikendom i kada su plaće dopuštale da se poprave kočnice, upravljač, ovjes, rasplinjač, generator i obnovi sustav hlađenja. Ogromna količina vremena potrošena je na jednostavno rastavljanje kromiranih dijelova, čišćenje i poliranje te ponovno sastavljanje stvari. Nekoliko dana prije mog 40. rođendana, auto se pojavio i morao sam izaći i voziti ga uokolo. I vozio sam ga, krenuvši na odiseju od oko 900 milja tijekom četiri dana.
Jedna stvar koja je brzo postala očita je nedostatak audio tehnologije. Siguran sam da je u 1960-ima bilo mnogo AM radio postaja za odabir, ali danas su mogućnosti jako ograničene.
Za vožnju sam koristio prijenosni Bluetooth zvučnik, što je dovelo do još jednog problema - punjenja svih ovih uređaja. Ispostavilo se da je dodatna utičnica od 12 volti, poznata kao upaljač za cigarete 1962. godine, prestala raditi. Pa sam nosio prijenosnu bateriju. Dva telefona, paket za punjenje i svi povezani kabeli napravili su apsolutnu zbrku zamršenih besmislica naprijed. Što je još gore, zvučnik se jedva čuo pri brzinama na autocesti sa spuštenim prozorima, što je u kolovozu bilo neophodno u mom automobilu bez klima uređaja.
Mora postojati bolji način.
Prvi dio:Moderna glavna jedinica
Prvo pitanje koje je trebalo riješiti bila je glavna jedinica. Moguće je prebacivanje na AM/FM stereo uređaj iz 1963. i naknadno postavljanje Bluetooth pojasa putem FM odašiljača. AM/FM radio iz te godine specifičan je za Thunderbird, rijedak je kao kokošji zub i skup je čak iu neispravnom stanju. Dodajte još oko 300 USD potrebnih popravaka plus cijena odašiljača i ovaj projekt može brzo preći 1500 USD.
Dostupna su naknadna rješenja, a neko sam vrijeme čak razmišljao o zamjeni svoje tvorničke jedinice za jednu od opcija dizajniranih za ispravan izgled iz klasičnih auto stereoa. Najbliža stvar mom izvornom radiju je reprodukcija opcijskog AM/FM radija iz 1963. S 45 watta x 4 kanala snage, Bluetooth mogućnostima, pomoćnim ulazom i pet predizlaza, ovaj stereo je dobra opcija za originalnost. Po cijeni od oko 687,50 dolara, neoriginalni radio je skupa kupovina. I dok nudi mnoge značajke, neke od stvari koje sam zavolio, poput Android Auta, jednostavno nisu moguće s dvostupnim radiom.
Većina ljudi vjerojatno ne bi primijetila ništa drugačije, ali znam svoj ukus i smetao bi mi stereo iz 1963. u mom Thunderbirdu iz 1962. Bez recenzije određenog stereo uređaja iz Classic Car Stereos, a brojni recenzenti koji su imali značajne probleme s jamstvenim zahtjevima za druge proizvode, bio sam poprilično oprezan što sam dao toliki dio novca na proizvod tvrtke koja nisam. upoznat s korištenjem.
Nakratko sam se poigravao s idejom korištenja tableta i niza bežičnih zvučnika, ali praktičnost tog plana nije rezultirala dugoročnim rješenjem. Međutim, volim imati navigaciju. Imajući to na umu, igrao sam se s idejom tableta za navigaciju i daljinskog stereo uređaja skrivenog negdje drugdje u autu.
Niti jedna od ovih ideja zapravo ne odgovara onome što sam želio od stereo glavne jedinice. Svaka je opcija bila neka razina neinspirativnog kompromisa.
Ah-ha trenutak
U tjednima koje sam proveo rastavljajući, čisteći i ponovno sastavljajući unutrašnjost, primijetio sam da nedostatak klime u mom automobilu otvara mogućnost prilagođene stereo instalacije. Dok sam radio na čišćenju desetljećima prljavštine s nabora ispod svoje ploče, zamišljao sam kako bi moderna glavna jedinica pristajala.
Imam dugogodišnje iskustvo rada na klasičnim automobilima. Jedna od stvari koja me stvarno ljuti je kad sjednem u lijepi primjerak klasičnog vozila i vidim da je ploča iskasapljena da u nju stane radio s jednim din-om. Oštećenje učinjeno na kontrolnoj ploči dizajniranoj za radio s dva stupa uglavnom se ne može popraviti, zauvijek mijenja automobil i vječno je tužno.
Ono što sam namjeravao učiniti bilo je instalirati potpuno modernu glavnu jedinicu sa zaslonom osjetljivim na dodir koja ima puno snage, s tonom modernih značajki povezivanja i instalirati je u Thunderbird iz 1962. bez trajnog mijenjanja automobila na bilo koji način.
Postavljanje Sony XAV-AX7000
S aluminijskom pločom i izolacijom koja blokira rupu gdje bi bio AC registar da sam imao AC, otkriva se prostor širok oko 9 inča na najvećem i oko 7 inča na najužem. Iza aluminijske ploče nalazi se šupljina duboka otprilike 7” na najplićem dijelu. Moje poluge kontrole klime i kabeli prolaze duž gornjeg dijela mjenjača ispod ovog prostora. Iza je jedinstvena kutija grijača za automobile bez klima uređaja. Ako želite pročitati više o glavnoj jedinici, napravio sam potpuni opis i recenziju XAV-AX7000.
Ovaj prostor, kako se pokazalo, radi fantastično dobro sa Sony XAV-AX7000 koji instaliram. Ploča s instrumentima nije vodoravna, već je blago postupna zakrivljena. Instaliranje radija duž krivulje ploče malo će nagnuti jedinicu, dopuštajući joj da savršeno oslobodi krakove kontrolnog kabela na mojoj kutiji grijača.
Recikliraj, ponovno upotrijebi, prenamijeni
Obratio sam se Charlieju Watkinsu iz Watkins Restorations u Oregonu i on mi je uspio poslati potpunu, originalnu i neoštećenu desnu instrument ploču od neke nesretne 'ptice kojoj više nije trebala. Na ovaj način nisam žrtvovao svoje izvorne dijelove. Da želim, mogao bih se vratiti na izvornu crticu bez znakova zlouporabe.
Nakon uklanjanja svih kromiranih ukrasa, ukrasa od nehrđajućeg čelika i uklanjanja vijaka koji pričvršćuju jastučiće za koljena i ploče koje završavaju područje od vrata do ploče, aluminijska ploča se nježno odvaja. Drži se na mjestu samo pomoću ljepila koje se ne stvrdnjava i napetosti svih obloga.
Savjet dana:ostanite organizirani. Ako imate pri ruci staru kutiju za jaja, ona je vrlo dobra za spremanje vijaka, kopči i drugih sitnica. Ne zaboravite označiti svoje dijelove. Volim u Dollar Storeu dobiti vrećice za pohranu na koje se može pisati flomasterom.
Izrada uzorka
Lako je zamisliti moderan stereo u klasičnom automobilu, ali za njegovo stvarno ostvarenje potrebno je malo rada, malo strpljenja i puno mjerenja, testiranja, mjerenja itd.
Nakon što su moji originalni dijelovi uklonjeni, testiram odgovara li zamjenska ploča. Zalijepio sam samoljepljivu traku sa stražnje strane na mjesto gdje bi se nalazio otvor. S čvrsto pritisnutom pločom na mjestu i poredanim rupama za kopče, nacrtao sam liniju oko otvora na maskirnu traku.
Precizno sam izmjerio točnu veličinu dijela Sony zaslona koji sam želio stršati izvan ploče i napravio uzorak u tvrdom kartonu. Nakon što sam se uvjerio da uzorak čvrsto pristaje, locirao sam uzorak na stražnjoj strani aluminijske ploče.
Sa svojim uzorkom iscrtanim na stražnjoj strani upravljačke ploče, izvadio sam rotirajući alat s reznim kotačićem dizajniranim za metal. Vrlo pažljivo sam zarezao duž linije i otvorio rupu.
Kad sam napravio svoj uzorak, odlučio sam postaviti glavnu jedinicu što je moguće čvršće, a zatim sam nacrtao uzorak na svoj metal unutar uzorka. Zbog toga je otvor bio malo premalen. Upotrijebio sam rašpicu s ravnom stranom kako bih nježno otvorio rupu kako bi savršeno pristajao stereo uređaju.
Mounting Up
The Sony XAV-AX7000 is a single-din case with a double-din screen that measures just under 7”. Mounting options are not included with the head unit, so installers either have to purchase an aftermarket bracket or fabricate.
This was a tempting place to discard my intention to avoid damaging anything. Fabricating brackets was not hard, but sufficiently mounting them was another story. Drilling a few holes behind the dash wouldn’t ever show, anyway, but I would know it was there.
What I decided to do was to fabricate brackets that mounted using the holes intended for retaining the AC register. These holes were simply empty on my car, so I used a few small machine screws to mount brackets at either side.
I wanted the head unit to sit at an angle, and the brackets needed to be angled to enable the head unit to sit securely. Figuring this angle was simple using a little high school geometry, a level, and a tape measure.
I used the level and tape measure to find the rise and run of the triangle, then used the Pythagorean Theorem to solve for the hypotenuse. Don’t worry, I Googled it also.
What I found was that I needed an angle of 27 degrees to allow the bracket to align with the M6x4 screw holes in the chassis of the head unit. I used simple steel straps to fabricate my brackets. They are cheap, easy to bend, and durable.
With my brackets bent and trimmed, I mocked the unit up to the dash and checked for clearance issues or binding. Everything looked pretty good. I tightened the brackets into place, sliding the head unit in between, and reinstalled the newly-trimmed dash panel. The head unit barely fits through the opening, to the point that extreme care needs to be taken to avoid scuffing the screen on the aluminum edges. With the unit held in place, I put the screws into the brackets and tightened down the head unit.
Even without the trim in place, I could tell I made a good decision on the head unit. It simply was understated and blended right in with all the other textures and materials around it, while maintaining its modernity.
Wiring it Up
Sticking with the theme that I wanted to be able to undo all the custom work without leaving any permanent damage, I ran all-new wiring to the Sony XAV-AX7000 head unit. This was probably necessary anyway, as the original stereo was not a powerhouse.
Don’t forget to disconnect the battery before beginning.
Constant Power
Per the instructions included with the Sony, I ran a 14 ga wire from the 12 Volt positive post on my starter solenoid to the head unit. I verified this with the key off and a voltmeter.
On the Sony wiring harness, the constant power wire is yellow, so that is what I ran also. I used waterproof crimp connectors that have heat shrink sleeves. I particularly like these connectors under the hood, where all sorts of nasty things happen. Corroded 12V positive connectors can be very dangerous.
I installed a blade-type 15 amp inline fuse a few inches from the battery connection. This fuse will help prevent sudden surges of power that could damage the Sony head unit.
I secured the yellow wire with electrical tape alongside the wire that runs from the starter solenoid to the voltage regulator in my Thunderbird. I took advantage of a conveniently located factory grommet in the firewall and slipped the yellow wire through right behind the factory stereo.
Switched Power
Dropping the ignition switch to access the switched 12 volt connection required that the left side of the dash be unbolted. Most ignition switches can be removed using a paperclip and the ignition key. Turning the ignition switch to the ACC setting exposes a small pin in a hole in the face of the tumbler. Pressing this gently with a paperclip while continuing to turn the key counter-clockwise will release the tumbler. Then, simply press the switch toward the dash and turn slightly.
The factory wiring in my Thunderbird is very tightly bundled. There are very few areas where the wiring is easily accessible. This was a well-built car in its day, and the attention to detail shows in how well the wiring has held up.
I did not undo any factory wiring or change the routing of any of the factory items. I didn’t remove any wiring from the original stereo. This way, if I want to revert to an original car, I simply remove the wiring I ran and nothing else needs to be done. My car remains entirely original.
I used another shrinkable weatherproof connector to connect to the ACC post on the back of my ignition switch. I carefully routed the wire above the light switch and into the rear of the dash. The Sony harness uses a red wire here, and so I did also. I used the same 14ga diameter as in the constant power supply.
Finding the ACC switch position is easy. Simply put the tumbler back into the switch, reconnect the battery, and test the posts on the ignition switch. One post will have power even in the off position. Another will only have power in the ACC position. On Ford ignition switches, this is almost always the exposed post on the rear of the switch.
Avoiding Obstacles
The third generation Thunderbird had a unique feature called Swing-Away steering. When the transmission lever is lifted up, the steering wheel swings toward the center of the car. Door hinges that allow nearly 90 degrees of opening coupled with the swing away steering wheel make for one of the easiest cars to get in and out of.
That cool sliding steering wheel also presents unique problems. In order to ensure that the wiring did not become tangled in the sliding mechanism, it meant that the wires had to be very carefully positioned and secured. I was able to use several factory wire clips that retained original wiring harnesses and passed the wire to the head unit with the help of a DIY fish tape made from a metal coat hanger.
The first time I ran the wire through, I did not pay enough attention to the location of the windshield wiper mechanism. My original location could have possibly gotten tangled up in the wiper arms, causing damage to any number of things. I rerouted the wire, making sure that it was tightly secured with no loose loops.
This is one of those tasks where taking the time to ensure everything is correct can save immeasurable time later down the road.
I should have installed the microphone at this point. I did not, and ended up having to try and install it after the car was put completely back together. It did not work out.
I installed the microphone wire behind the chrome trim on the windshield pillar. The supplied clip worked great for attaching the microphone discreetly to my sun visor.
Grounding it Out
The Sony unit requires that a lead be connected to the parking brake illumination point. This tells the head unit the car is not being driven.
This was something I did not want to undertake, as it would mean cutting into the wiring. Instead, I routed the parking brake wire to the same point as my ground strap. Using a shrinkable crimp connector, I connected the ground and parking brake wires. I used an existing ground point and tightened it down.
With some head units, grounding out the parking brake wire will allow Android Auto and other features to function. In many instances, a trigger adapter is required. These are available from aftermarket companies.
Turning it On
These three connections allowed me to start the stereo up and see how it looked sitting in the driver's seat. It looked fantastic. I could easily reach the screen, and even in broad daylight, the screen was clear and easy to read. Once the microphone was connected, I could take advantage of voice commands to control the unit, but it was important to me that the screen also be easily accessible when driving.
I decided that my brackets could use a little adjustment, so I went ahead and took everything apart, made some changes to the brackets including adding a channel for adjusting the clamping point on the head unit, and refit everything.
The Sony XAV-AX7000 is truly a wonderful bit of technology. The screen is clear and easy to see, and when you tap on an icon, it is instantly responsive. The menus are intuitive, and it is very easy to quickly get to what you want. The home screen is among the best I have used. I like simple, and the home screen is as simple as it gets. No guessing what the icon means here, just select what you want and away you go.
The next project would be addressing the factory speaker.
Part Two:Modern Speakers
The factory dash speaker in the 1962 Thunderbird is a paper cone 6×9. Even in its day, this speaker was not very good, and 57 years of sitting in the dash did this one no favors. While the speaker does not appear to have any actual damage, the 45 watts of power the Sony XAV-AX7000 pumps out is going to be way too much for this old speaker.
Aftermarket solutions are plentiful. Ford engineers decision to use a common speaker size plays in the favor of drivers looking for custom sound. A whole lot of vintage cars use odd sized speakers that are difficult to upgrade, but not this old Thunderbird.
It seemed to me that it would be a shame to install this beautiful touchscreen head unit and hook it up to a stock-style mono speaker. It is a good thing I set my sights on something other than stock, though, as the stock replacement speaker has been discontinued Today, all the aftermarket solutions use a single 6×9 with dual voice coils. Crutchfield lists one for $89.99 that is produced by RetroSound.
I am not crazy about a single speaker playing both left and right channels, and I wasn’t too interested in spending $90 on one speaker, either.
I found a really slick set-up built by Custom AutoSound that uses dual 4” speakers mounted on a plate designed to attach in place of a factory 6×9 dash speaker. At $74.95 through Classic Car Stereos -and preloaded with Kicker CS speakers- this option was still quite expensive.
I recently reviewed the Kicker CS-series speakers and knew they were a good speaker. I also knew that a pair of 4” Kicker CSC4 Coaxial speakers run less than $50. Amazon Prime hooked it up with same-day delivery.
The factory speaker is removed easily. The dash grill clips in place, so a gentle pry on the front edge and the cover pops up and slides out of the way. The factory speaker has two screws retaining it to the dash. With these removed, the speaker lifts up and is disconnected from the wiring.
Fabricating a Bracket
With the factory speaker removed from its mount, the 4” Kickers line up very nicely inside the space, but will require a custom-made mount. Almost any rigid material will work here. I have seen custom speaker mounts in wood, plastic, metal, and just about everything else.
I decided to use acrylic because I had the right size of a scrap from a previous project on hand. I dislike working with acrylic, but it does provide a nice, stable surface to mount speakers into.
I used the original factory grill to make a pattern drawn out directly on the acrylic with a felt-tip marker. I used a cutting bit on a rotary tool to cut out the needed shapes, then used a round rasp and a grinding bit to smooth and enlarge the speaker openings for a tight installation.
Once the speakers could fit inside the mounting hole, I drilled the holes for the speaker retaining screws. I mounted the speakers up and took some pictures of my DIY dash speaker.
Installing the speakers into the dash was a little different than removal. The Kicker CS-series have a very low profile tweeter dome, but it is still larger than the nonexistent dome of the factory speaker. Even when mounted underneath the acrylic, the tweeter touched the metal grill cover.
In order to mount the speaker, I decided to attach it from underneath the dash. The speaker opening provides abundant room, so I was able to shimmy the speakers into the hole. I had to remove the factory radio to access the speaker mounting screws.
In the Thunderbird, an access panel below the stereo needs to be removed to loosen the stereo retaining bolt. The knobs on the face of the stereo simply pull off, revealing the retaining nuts. Once these are removed, the diecast face of the radio comes off and the head unit can be pushed back into the dash.
I didn’t want to take the head unit all the way out to mount the speakers, as there would be no way to get it back in the dash. Fortunately, there was plenty of clearance to move the stereo to one side.
Aligning the mounting screws and tightening it all down was a bit of a pain, but I eventually got it. Now, the brand new Kicker CS4s have plenty of clearance and the dash still looks factory correct. I did not alter anything in this installation, and I saved the screws and clips I did not reuse along with the factory speaker.
After I had the original head unit reinstalled, I fired up the Sony XAV-AX7000 to see how the dual dash speakers sound.
Centrally located dash speakers are not an ideal location for good sounding music. I was quite surprised by the richness the Kicker speakers produce in the dash. The speakers are very clear, if a little high-pitched, but lacking any supporting speakers, they sound very good.
The more I played with the Sony XAV-AX7000, the more I came to like it’s features. Adjusting the tone and speaker settings was straight-forward and immediately improved the sound quality of my set-up.
Bluetooth set-up was simple and fast, and in a brief time, I had Pandora running on screen. Pretty slick.
Many users of the Sony XAV-AX7000 will be able to use Android Auto and Apple CarPlay wirelessly, but not me. I have an older phone that I am not ready to replace yet, but it requires that I use one of the USB leads in the back of the head unit to run Android Auto.
On to Part Three!
Part Three:Concealed USB Ports
Now that I had the Sony XAV-AX7000 wired up and playing through dual Kicker CS4 speakers in my dash, I needed to have a way to plug my phone in without wires dangling everywhere, and, of course, not damaging anything.
The solution is a dual port USB plug. Amazon Prime had exactly what I was looking for with same-day delivery.
I decided that I wanted to install the USB port inside the locking center console that serves double duty as the glove box. I would need to remove the rest of the trim to get the glove box out and run the wires.
Ford went crazy with the stainless steel screws in this car. Almost every bit of trim is held down with several screws and clips. It is really important to stay organized when undertaking a project like this. There is simply no way the average person is going to remember where each screw goes.
With the glove box tray and the ashtray removed from the center console, I could see that the best place to run the wires was off to the passenger side underneath the center console.
I wanted a nice, tight, professional fit, so I measured the plug carefully, drilled a smaller than needed hole, and used a round file to open the hole up to the correct size. The plug fits great.
As I reassembled the console and ashtray assembly, I found that the USB extensions interfered with the hinged lid of the ashtray. It took some wiggling, but I finally got the wires to sit in such a way as to permit the lid to open all of the way.
With the cables pulled through the console, it was just a matter of connecting them to the Sony XAV-AX7000. The head unit has two USB ports, but they are not equal. Port #1 is intended for smartphone connection, while Port #2 is designed for USB storage devices and charging purposes.
I plugged my phone into the top USB port and connected the #1 USB lead, and viola , I had a direct connection. The Sony head unit immediately switched to smartphone mode and brought Android Auto up on screen, complete with Google Maps on a satellite image showing me in my yard.
This was an easy little project that took less than an hour to do and added the instant convenience of USB connectivity, phone charging capabilities, and no wiring hanging around the cockpit. As a bonus, my center console lid locks, so I can forget my phone in relative security.
Part 4:Backup Camera Installation
The 1961-63 Thunderbird introduced a feature that has become nearly universal, the floating rear view mirror. Every car prior to the Thunderbird used some type of physical mount to the dash, windshield, or wherever to hold the rear view mirror.
The original rear view mirror is a thing of beauty. It hangs from an adjustable aluminum mount and is a spectacle of chrome-plated metal and glass, complete with a Day/Night rocker switch.
The problem is that this mirror is very heavy. I have not been able to keep mine glued in place for more than a few days. It is rather startling to be cruising down the road and suddenly have this large, chrome mirror crashing down on you. I have mine in the car, but I have given up gluing it in place.
The 7” monitor on the Sony XAV-AX7000 is a truly beautiful, glare-resistant piece of technology. With built-in backup camera capabilities, I figured, why not use a backup camera as a rear view mirror?
I decided on a micro-camera from Esky to serve as my rear view camera. This camera is small and lightweight, two key things to me. You can also find a great list of the Best Rear View Backup Cameras.
I wanted to install the camera on the inside of the rear glass and attach it along the center trim. To avoid damaging the trim, I decided to use a small piece of velcro. With the camera temporarily in place, I wired it up and checked the picture. My window was extremely dirty, but the image looked pretty good, so I got to disassembling.
First, the rear seat had to come out. Classic car seats are all about the same -the bottom is clipped in place, while the top section is retained with a few bolts. I removed all of the chrome trim around the window, across the sail panel, and also removed the drivers side rear side panel along with all the window switch wiring.
The Esky camera is tiny, but the connections to it are bulky. The camera requires an RCA connector that feeds the video signal and a second RCA-type cable for powering the camera. These connectors were not far enough away from my mounting location to be easily hidden, so I had to come up with a solution.
What I ended up doing was removing the dome light and a couple of the staples that hold the headliner in place along the rear window. I very carefully fed the RCA connectors and extra wiring between the headliner and the roof of the car into a hollow space created by the dome light housing.
The name of this project is to upgrade without altering anything, and in order to stay true to that goal, I had to extend the ground wire about eight inches to use an existing ground point rather than simply throwing a self-tapping sheet metal screw into metal behind the seat.
I ran the RCA and Power cables behind the rear side panel, through a gap in the structure, and under the sill plates. I removed the front drivers side kick panel and ran the wiring behind the panel into the dash.
Now, here is where everything got a little complicated.
The connections seemed like they should be obvious. The RCA camera plugs into the Camera port on the Sony XAV-AX7000 and the power connection goes to the ACC terminal. The Reverse IN wire on the Sony harness connects to the reverse switch, which is not what I wanted to do.
I wanted to be able to turn on the camera any time I wanted, so I needed to wire the camera a little different. A couple of extremely helpful emails with the customer service reps at Esky and I realized that the trigger wire for the RCA cable needs to be wired to 12 volt power and the Reverse IN wire needs to connect to the trigger wire on the RCA cable.
In order to allow the camera to be turned on all the time, I needed to wire in a toggle switch. I decided to use 16 gauge green wire for the camera so I could easily tell it apart from other wiring. I used crimp connectors with shrink wrap sleeves for the ACC connection and connecting the switch.
Today’s Pro Tip:Be patient. Fabrication is never easy, and when you try and rush things, mistakes happen.
Case in point:
I drilled the hole to mount the toggle switch near the opening for the head unit in the aluminum dash. I needed a slightly bigger than ⅜” hole. I started out drilling a small pilot hole, then moved to a larger bit. I got impatient. The sun was going down and I wanted to get the switch wired up before dark. Instead of slowly progressing to a ⅜” bit, then filing the hole, I grabbed a brand-new 1⁄2” drill bit and went at it.
The drill bit stuck in the aluminum, and being a soft metal, simply shredded an egg-shaped hole nearly ¾” in diameter. My toggle switch would not mount, and worse, the aluminum dash I was working with was now badly damaged.
My options were limited, so I used a couple of flat washers, polished them up a little, and sandwiched the busted dash together. While not the super clean look I was going for, the washers did allow me to recess the face of the switch into the dash for a clean, flush finish.
Getting the camera up and running took a couple days and lots of disassembly and reassembly. I spent nearly half a day removing and replacing the interior of the car just to run the wires. A major issue with this camera is the included instructions that simply omit the trigger lead on the RCA cable from all wiring diagrams. When I reached out to Esky, they emailed me a proper wiring diagram that matched up with the components I had. In fact, they even sent a series of follow-up emails just to be sure I was satisfied with my camera. Great company, in my opinion.
The camera works okay, though the image is a little distorted due to the curvature of the back window glass and the wide angle lens picks up reflections. At night in total darkness, it is not easy to see what is behind the car. The Esky camera does not use IR technology, so I didn’t expect much, but the view at night is basically useless when glare is present. The toggle switch makes using the camera extremely convenient.
Unfortunately, it does not seem possible to get rid of the parking lines the camera applies. Because my camera is mounted inside the rear glass, the parking lines make no sense whatsoever. The velcro proved to be a temporary solution on a warm afternoon, so I reassessed the mount and decided I could carefully bend and wedge the lip of the camera under the trim.
It is important to take these projects slowly and progress one step at a time. Minor mistakes can create major problems. When I tried to install the microphone after I had installed the head unit, I accidentally broke the center pin of the RCA cable supplied with the Esky camera inside the Sony head unit. I had to order a new RCA cable, which I will then have to install. That means doing this entire step over again.
Project Completion
Now that I have the Sony XAV-AX7000 installed in the 1962 Thunderbird with custom 4” Kicker CS speakers in the dash and a backup camera from Esky, this old car is nearly as technologically rich as a modern cruiser. Of course, I still have lap belts (aftermarket, since seat belts were an option in 1962), no air bags or safety sensors, or pretty much any other safety feature, but I can text and drive hands-free, get directions to the nearest gas station, and rock out all day.
The Sony XAV-AX7000 head unit is a winner. It provides plenty of power, is easy to control, and has a complete range of options to connect to a wide assortment of devices. The head unit is a pleasure to use when driving. Android Auto running from an older phone works flawlessly.
The backup camera is probably the biggest disappointment. I was hoping to get a properly usable image, but it seems that in most light, the camera focuses on the reflections and glare on the back glass instead of what lies behind me. In most light, I can tell if someone or something is behind me, but the details are fuzzy.
At higher volumes, the dash speaker set-up has some reverb or rattling that is annoying, and the little 4” Kickers do not handle bass well. Given the frequency response of the speakers, I didn’t expect to get thunder, but the distorted bass is distracting and will require reassessment. It is possible that I could have used 5 ¼” speakers with some wiggling to get them within the dash, but mounting options almost certainly would have meant altering the dash in some way.
The total installation took place over the course of several days. I wish the toggle switch installation would have gone better, but overall, I am happy with the results. I think the Sony head unit looks excellent in place, and the sound is so much better than the original AM radio or the bluetooth speaker I used. I am very happy with how the head unit sits in the dash, and how easy it is to operate.
The 1962 Thunderbird has always represented a triumphant, glorious future to me. I have always seen the car as Ford’s vision of the future. Upgrading the head unit, for me, is a step in keeping the car driveable and safe, while adding the futuristic connectivity options modern car owners enjoy. I think this custom set-up provides all the futuristic options this old ‘Bird deserves without functionally altering the car in any way.
Cost of Install:
- Sony XAV-AX7000:$599.99
(Note* This head unit was provided for free by Sony for the purpose of an unbiased review. This is the second car it has been installed in)
- Kicker CS4:$49.95
- USB Plug:$10.80
- Backup Camera:$16.99
- Various electrical wire:$21
- Various Electrical Connectors:$12
- Electrical Tape:$2
I used metal construction straps for the brackets and a piece of spare acrylic for the speaker mount, all of which I had just laying around, so these items were free. Figure between $3 and $10 for materials to fabricate brackets.
Total Cost of Upgrade:$712.73