Kako ugraditi pojačalo u Jeep JK?

Svaki vlasnik automobila želi imati dobar zvučni sustav s ugrađenim pojačalom, koji se ne razlikuje od vozača Jeep Wrangler JK.

Ali kako instalirati pojačalo u Jeep Wrangler JK? Saznajmo.

Ugradnja pojačala u vaš Jeep Wrangler JK zahtijeva da napravite dobar prostor za postavljanje pojačala, a mnogi ga više vole staviti ispod prednjeg sjedala. Zatim, nakon što osigurate prostor za pojačalo, pronađite bolji način za poravnavanje žica na različitim mjestima zvučnika u automobilu. Na kraju, opskrbite pojačalo stabilnom i dosljednom snagom i provjerite je li ožičenje izvedeno ispravno.

U ovom ću vam članku pokazati kako se nositi s pojačalom u Jeepu JK i kako ga ispravno instalirati.

Kako instalirati pojačalo u Jeep JK s naknadnim radiom?

Prije instaliranja pojačala na naknadni radio, provjerite jesu li pokrivene sve potrebe i mjere opreza. Najbolje mjesto za postavljanje pojačala je prtljažnik, posebno kada se montira veliki model.

• Pričvrstite pojačalo vijcima unutar prethodno izbušenih rupa.

• Spojite kabele za napajanje na bateriju u kabini vašeg Jeepa i produžite ih do mjesta gdje je ugrađeno pojačalo.

• Zatim spojite žicu za uzemljenje na pojačalo i izravno na šasiju automobila.

Prilikom postavljanja žice za uzemljenje, pazite da dođe u kontakt s metalom jer može utjecati na opću izvedbu pojačala.

• Identificirajte žice koje povezuju ove zvučnike s postprodajnim radiom i ocrtajte ih tako da otvore i negativne i pozitivne žice.

• Spojite žicu zvučnika na prugaste položaje i zategnite ih pomoću električne trake.

• Spojite žice na pojačalo i provjerite je li svaka žica savršeno postavljena. Provjerite spajate li prave zvučnike na prave kanale.

• Ponovo spojite priključke akumulatora automobila kako biste provjerili je li cijela veza pojačala na mjestu.

Nakon što ga uključite i ništa se ne događa, ponovno spojite kabel za napajanje na akumulator automobila i provjerite ožičenje. U ovom trenutku, pojačalo je u izvrsnoj poziciji za koordinaciju s naknadnim radiom.

Instalacija pojačala

Ugradnja pojačala u Jeep Wrangler JK nije tako jednostavna kao što možda zvuči. Morate biti zadovoljni i imati osnovne informacije o tome kako pojačalo radi i kako radi zajedno sa stereo uređajem u automobilu.

Imajte na umu da je pojačalo vitalni dio opreme koji značajno pridonosi visokokvalitetnom zvuku koji proizvode zvučnici.

Morate stvoriti dosta prostora za ugradnju pojačala i za spajanje žica. Većina pojačala postavlja se ili ispod sjedala ili u prtljažniku, gdje možete osigurati dobar prostor koji je siguran za njihovu ugradnju, ali i za druge komponente.

Mnogi se odlučuju za ugradnju pojačala ispod suvozačevog sjedala kako bi izbjegli neugodnosti. Također, ugradnja pojačala ispod prednjeg sjedala jednostavan je zadatak koji ne uključuje mnogo složenosti, osim provlačenja žica kroz kabinu.

Osim toga, postavljanje pojačala na pod Jeep Wranglera izlaže ga potencijalnoj opasnosti od utjecaja vlage ili prašine.

Koji su vam alati potrebni za instaliranje pojačala u Wrangler JK?

Mnoga pojačala dolaze s potpunim ožičenjem , smanjujući dodatnu potragu za žicama ili konektorima, ali radije bih nabavio zasebne žice u točnoj veličini koju trebam za određeni sustav.

Sjajne žice koje koristim su od Knukonceptza , pa ako želite dobiti nešto najbolje kvalitete, pogledajte ih na Amazonu.

Još jedna stvar koju morate imati kada instalirate pojačalo je umetnuti osigurač . Provjerite koristite li vrstu osigurača koju preporučuje proizvođač pojačala.

Također će vam trebati žica za uzemljenje, žice za daljinsko uključivanje, RCA kabeli, utikači za konektore i samo pojačalo. Ne zaboravite da konektori moraju savršeno odgovarati priključnim terminalima i veličinama žica.

Osim toga, veličina pojačala koje kupite automatski će odrediti količinu prostora koji vam je potreban, a ako imate ograničen prostor u automobilu, razmislite o postavljanju ispod, iza ili između sjedala.

Također, zapamtite da pojačala stvaraju toplinu i trebaju neki oblik hlađenja. To znači da položaj na koji postavljate svoje pojačalo treba omogućiti slobodno kretanje zraka.

Ako montirate subwoofer, odlična je ideja instalirati pojačalo izravno u kućište.

Razmislite kako ćete izvesti ožičenje od pojačala do glavne jedinice stereo uređaja i napajanje iz akumulatora automobila. Dobro je provesti ožičenje ispod podne obloge preko donjih pragova vrata.

RCA kabeli trebaju biti čvrsto postavljeni na suprotnom dijelu automobila u odnosu na strujne žice kako bi se uklonio svaki oblik smetnji. Pronađite položaj osigurača vašeg pojačala ispod haube i pronađite najkraći mogući put do njega.

The power cable should pass through the firewall for safety purposes. Try using the existing holes available to avoid drilling new holes across the firewall.

How to Fit the Amplifier in the Jeep Wrangler JK?

Before beginning the fitting process, ensure you have enough wiring to clear the job.

If the wiring is not enough, locate the best position to place the amplifier that will work perfectly with the wiring you have at hand.

Disconnect the positive terminal of the battery before beginning any work. Besides, ensure that you clearly understand what is behind the spot where you want to drill a hole. This will help you to avoid damaging any components.

To make a perfect hole, start by making a small pilot hole, then drill out the ideal hole size you need to use.

Next, fit a rubber grommet in the hole to prevent the sharp steel edge from damaging the wire.

Position the amplifier perfectly and mark the mounting holes with a pencil or any form of marker. Then, go ahead and drill the holes where the amplifier is located.

Run all the wiring in the perfect positions and cut them depending on the required length. Do not make wires too short. It is better to have a one foot extra than missing 2″.

How to Wire the Amplifier in a Jeep Wrangler JK?

Eliminate the insulation from all ends of the wires to give room to attach the connectors.

Note that some amplifiers require a connection using only bare wires, especially for the power wires.

Connect the ground wire to a metal point connected to the Jeep’s chassis or the best grounding point available. The ground wire should be placed directly to the bare chassis metal, not the painted surface, so you have to clean any form of paint to ensure excellent ground connection.

Connect the RCA leads, speaker leads, and the remote turn-on system from the amplifier directly to the back of the head unit. However, some head units do not have the remote turn-on wire option. In this case, wire the remote turn-on of the amp to the power wire connecting the head unit or another wire running the accessory switch, or you may need to add an on/off switch on the amplifier power wire.

This is mainly meant to help avoid the amplifier remaining on once you have switched off your ignition, and it prevents the amplifier from draining off your car battery without your consent.

Connect the rear, front, and the wires of the subwoofer speaker from the amplifier to the other corresponding speakers.

Connect the inline fuse to the primary power cable holding all the connections to the end of the leads.

The fuse holder needs to be installed on a solid structure inside the engine space, ideally no longer than 18″ from the battery’s positive terminal.

Connect the amp power cable to the battery’s positive lead and reconnect the positive battery lead to the positive terminal.

After the power supply is on, secure all the wiring using the cable ties. At this point, you need to test all the amplifier operations using the fade, balance, and subwoofer settings on the head unit.

Ensure that every speaker is working independently without any static or distortion.

Benefits of Using One Amplifier for Speakers and Subwoofer

Installing an efficient amplifier in your Jeep Wrangler JK comes with a bunch of benefits.

• Using one amplifier for all speakers save the battery from draining, increasing its lifespan.

• In addition, integrating one amplifier to the subwoofer and speakers is easier than setting up two amplifiers. This saves your time and the space to set up the amplifier. Remember, the amp needs some considerable space to accommodate the wiring.

A single amplifier is easy to balance and increases adaptability. This works better, especially if you have at least a five-channel amplifier.

Go for an advanced model with incredible power whenever you think about installing one amplifier to operate the speakers and the subwoofer.

Best Amplifiers for Jeep Wrangler JK

Boss Audio Riot

This is a classy mono-block from the Boss Audios Riot series which is is ideal for supplying power tot your subwoofer. The primary factor that makes it stand out is its low price and high quality. It’s made in the A/B class, with incredible abilities to generate exceptional output.

The amplifier can withstand high amounts of power output. It rocks with an impressive 1100 watts at only 2 ohms giving you a general RMS of about 825 watts. It comes with both high and low-level inputs that help it achieve an optimal performance.

This amplifier has a variable low pass filter that gives you total control of what penetrates through the car subwoofers.

The woofer levels can be easily controlled using a remote controller to boost the bass function. Its design can perfectly fit in the trunk or between the seats.

Rockford R300X4 Prime

Rockford is a fantastic four-channel amplifier choice that is also an excellent choice for Jeep Wrangler JK.

It is made in the A/B class, and it is equipped with a heat sink that ensures everything is running smoothly and does not overheat.

It is a versatile amplifier that can run the entire system smoothly without any complications. The amp can run all the components, including the front channels and the subwoofer at the bridge mode.

Rockville dB45

The Rockville car amplifier is a powerful audio system that perfectly fits a Jeep Wrangler JK. It generates a power output of 3200 watts to run all the speakers and the subwoofer in the car.

It has a four-channel output generating high output and a low impedance solution that can power the car’s bass speakers.

Besides, this amplifier features an incredible subsonic filter with a fully adjustable crossover.

The amp has a bunch of circuitry that enables users to adjust the bass settings depending on their preferred bass taste. It features an inbuilt soft start technology that prevents the amplifier system from starting on a high volume.

Zaključak

Installing an amplifier in a Jeep Wrangler JK from scratch is not the easiest task, but with the above-detailed guidance, you can easily acquire a new amplifier and install it in your car without any problem.

However, you need to ensure that you abide by all the precautions for your safety and your Jeep Wrangler JK. However, you need to ensure that you comply with the safeguards for your protection and your Jeep Wrangler JK.